Power Tool Accessories

Ridgid Adaptors For 819 Nipple Chuck E-729 1/8-Inch Bolt Adapter

Chuck Drill with Key Hc450

Chuck Jaws for 1224 Threading Machine

Chuck, with Key

Ridgid Drain Gun/Sink Machine (K-45, K-45-1, K-45AF-7)

Ridgid Holesaw Selection (Bi-Metal)

Ridgid K-1, K-3, K-6 Combination Closet Auger with C-Style Cutter Head

K-45-1 Sink Drain Cleaning Machine with Slide Action Chuck

Ridgid Nipple Chuck No. 819 12.7 mm (1/2") - 50.8 mm 9 2") w/ 5 adapters, carrier and wrench

Scroll, Chuck

Japan Hand Tap set 3pcs

Powerful motor for precise and rapid sawing up to 66 mm deep at 90° Safety switch prevents accidental starting Adapter included for attaching a vacuum cleaner if needed

Flex Shaft Fits Rotary Grinder Tool for Dremel Polishing Chuck (Black) - 36"

HT-12 Heavy Duty 1/2" Hand Tap (Silver)

HT-14 Heavy Duty 1/4" Hand Tap (Silver)

HT-316 Heavy Duty 3/16" Hand Tap (Silver)

HT-38 Heavy Duty 3/8" Hand Tap (Silver)

HT-516 Heavy Duty 5/16" Hand Tap (Silver)

HT-58 Heavy Duty 5/8" Hand Tap (Silver)

HT-716 Heavy Duty 7/16" Hand Tap (Silver)

HT-916 Heavy Duty 9/16" Hand Tap (Silver)

HT-M10 Heavy Duty 10mm Hand Tap (Silver)

HT-M12 Heavy Duty 12mm Hand Tap (Silver)

HT-M14 Heavy Duty 14mm Hand Tap (Silver)

HT-M16 Heavy Duty 16mm Hand Tap (Silver)

HT-M6 Heavy Duty 6mm Hand Tap (Silver)

HT-M8 Heavy Duty 8mm Hand Tap (Silver)

Stainless Steel Submersible Borehole Motor For 4" & 6" Well Casing Diameter

Stainless Steel Submersible Borehole Motor For 4" & 6" Well Casing Diameter High Quality Thrust Bearings The trust bearing is of the kingsburrY type lubricated by the internal fluid. During operation a wedge of water is drawn between the stainless steel pivot shoes and carbon disc to carry the thrust load generated by the pump. Located inside and at the bottom of the motor, the bearing is sealed away from sand and other contaminants. Sand Resistant Slinger and Lip Seals A stainless steel slinger and slinger guide are also closely fit to help prevent sand entry. Double rubber seals are installed to prevent well water and contaminants from entering the motor. High Reliable Carbon Bearing Two water lubricated carbon bearings are used as guide bearings. These have extremely large surface area and result in extra alignment support-less whipping and acts as a steady bushing. Water-Filled Design The motor lubrication is provided by the internal cooling water consistings of a water, anti-freeze and anti-rust mixture good to 30°C (-22°F). This mixture is installed at the factory. Two water plugs are located near of the top of the motor and are used by the installer to check the water level or to the top off needed before installation. Complete Corrosion and Water-Tight Protection All main motor components are made of stainless steel: including the can housing (water tight type motors have baked epoxy coated steel housing), Shaft and bolts. All other motor parts are coated with the baked epoxy coating.

This depends upon the depth of the borehole to ground level and then the distance from the ground level to the final end point e.g. where the water tank is sited. The further the distance, the higher the pressure requirements of the borehole pump to prevent the water from trickling out. Submersible borehole pumps are a type of submersible pump. They are centrifugal pumps driven by a submersible motor. As they usually draw in the fluid directly without a suction line, they must constantly be submerged in the fluid handled. Starter borehole pumps can run for up to 24 hours. However, your everyday borehole pump will run between 6 & 8 hours. It is not good for your borehole pump to run continuously. If you run electrical pumps continuously, your utility bill will skyrocket.